HP Virtual Connect SE F32 6x QSFP28 100GbE / 32Gb FC FibreChannel Network switch Module Synergy 12000 867796-B21

Physical Interfaces:
- 6x QSFP28 external uplink ports configurable as
1x100GbE, 1x40GbE, 4x25GbE 4x10GbE or 1x 25Gb 1x 10Gb Ethernet network ports or 1x 32Gb, 1x 16Gb, 1x 8Gb FC Fibre Channel connected to external LAN switches
- 12 x 25/50GbE downlinks to compute blade module Ethernet Adapters
- 1x RJ-45 port - not specified
- The FlexHBA can be configured to transport either Fiber Channel over Ethernet/CEE or Accelerated iSCSI protocol.
- Each FlexNIC and FlexHBA is recognized by the compute module as a PCIe physical function device with adjustable speeds from 250Mb to 25Gb in 250Mb increments when connected to a 2-port 25GbE Converged Network Adapter and from 500Mb to 50Gb in 500Mb increments when connected to a Dual-Port 50Gb Converged Network Adapter

- xtended list of direct attach copper cable connections supported
- Low latency (sub 1.0 µs Ethernet ports) throughput provides switch-like performance.
- Line-rate, full-duplex 6.4 Tbps bridging fabric
- MTU up to 9216 Bytes - Jumbo Frames
- Supports up to 48K L2 MAC entries
- VLAN Tagging and Link Aggregation supported on all uplinks
- Supports up to 4K IPMC entries

supported HPE Synergy Compute Modules
- HPE Synergy 480 Gen10
- HPE Synergy 660 Gen10
- HPE Synergy 480 Gen11

supported HPE Interconnect Link Module
- HPE Synergy 50Gb Interconnect Link Module

supported HPE Network Adapters
- HPE Synergy 4820C 10/20/25Gb Converged Network Adapter
- HPE Synergy 6820C 25/50Gb Converged Network Adapter

the maximum bandwidth of any QSFP28 port is 100Gbps, when 4x32Gbps Fibre Channel connections are used, each of the Fibre Channel connections signals for 32Gbps speed and setup but is limited to only 25Gbps bandwidth for that connection.

If a full 32Gbps bandwidth is desired for any QSFP28 port, then an HPE QSFP28/SFP28 adapter with a 32Gbps FC transceiver will populate the QSFP28 port.

In addition, the user must provision the uplink as a singular (1:1 or Q1 for example) uplink port to achieve the full 32Gbps for FC. If the port is configured in a 4:1 (Q1.1 for example) mode, then the port will be divided into 4 lanes with only 1 lane enabled and will only achieve 25Gbps speed.

Management
- Integrated composer based HPE OneView included with every frame, providing out-of-the-box for individual Virtual Connect configuration and management.
- Pre-configure compute modules I/O configurations prior to their installation for easy deployment
- Move, add, or change compute module network connections on the fly without impacting LAN and SAN administrator
- Monitoring via SNMPv1 & SNMPv2 and management via industry standard SNMPv3
- Compute module-side NPIV removes storage management constraint of a single physical HBA on a compute module does not add to SAN switch domains or require traditional SAN management
- Licensing support for native Fibre Channel through Composer powered by OneView

Trunking, Failover and Other Networking Features
- Shared Uplink Sets using Link Aggregation Control Protocol (LACP) allows the creation of Ethernet channeling with upstream switches that conform to IEEE 802.3ad. Ports can alternatively be configured for failover only.
- External ports within a Port Set can be on the same VC Ethernet module or on multiple VC modules within the Logical Interconnect.
- Supports 802.3ad Link Aggregation on server (downlink) ports.

VLAN Features
- 802.1Q VLAN supported on uplinks.
- Uplink ports can be configured for VLAN tagging at egress or pass-thru of tagged VLAN packets from Server ports.
- Native VLAN support for untagged packets on a shared uplink set.
- Packets can be targeted to a specific server ports.
- Simultaneous tunneled and mapped VLAN connections to a single logical interconnect.

Management Features
- Simple and intuitive Graphical User Interface (GUI) for defining, configuring, and managing all elements of Virtual Connect via composer based HPE OneView.
- Comprehensive administration, definition, and management of Ethernet Network, Shared Uplink Set, SAN Fabric management and Server Profiles.
- Embedded SNMPv3 agents allow Network Management applications to query Virtual Connect for statistics and trap information.
- Any uplink port and downlink port can be used as a dedicated mirrored port for traffic analysis and troubleshooting by a Network Analyzer.
- Domain Management of user accounts, frame, settings, and firmware updates MAC Address Administration allows local administration of predefined or user-defined MAC address ranges.
- WWN Address Administration allows local administration of predefined WWN addresses ranges to allow pre-provisioning of SAN volumes.
- Supported by composer based HPE OneView. Provides centralized network connection management and workload mobility for multiple compute modules.

Management and Standards Support
- INCITS FC-BB-5 Rev 2.00 (on all downlinks)
- IEEE 802.1Qbb
- IEEE 802.1Qaz
- IEEE 802.1AB LLDP
- IEEE 802.1Q (VLAN includes Native VLAN support and server side VLAN tag mapping)
- IEEE 802.2 LLC
- IEEE 802.3ad Link Aggregation
- Maximum of 48 LAGs
- Multi-Chassis Link Aggregation
- Maximum of 16 ports per MLAG
- Maximum of 24 uplink MLAGs
- IEEE 802.3ae 10Gb Fiber Ethernet
- IEEE 802.3aq 10Gb LRM Ethernet
- SNMPv3
- IPv6
- FC-BB5 aka FIP snooping on Q1-Q6

compatible with:

supported HPE Synergy Compute Modules
- HPE Synergy 480 Gen10
- HPE Synergy 660 Gen10
- HPE Synergy 480 Gen11

supported HPE Interconnect Link Module
- HPE Synergy 50Gb Interconnect Link Module

supported HPE Network Adapters
- HPE Synergy 4820C 10/20/25Gb Converged Network Adapter
- HPE Synergy 6820C 25/50Gb Converged Network Adapter

supported QSFP28 Transceivers for uplink ports
- HPE Synergy 100GbE/4x25GbE/4x32GbFC QSFP28 Transceiver 882251-B21
- HPE 100Gb QSFP28 MPO SR4 100m Transceiver 845966-B21
- Aruba 100G QSFP28 LC LR4 10km SMF 2-strand Transceiver JL310A
- HPE 100Gb QSFP28 Bidirectional Transceiver 845972-B21
- HPE X150 100G QSFP28 MPO PSM4 500m SM Transceiver JH420A
- HPE X150 100G QSFP28 CWDM4 2km SM Transceiver JH673A
- HPE X150 100G QSFP28 LC SWDM4 100m MM Transceiver JH419A